Drafts

Tämä standardi on laadittu eurooppalaisia yhdenmukaistettuja tuotestandardeja SFS-EN 1338, SFS-EN 1339,SFS-EN 1340, SFS-EN 1341, SFS-EN 1342 ja SFS-EN 1343 täydentäväksi kansalliseksi soveltamisstandardiksi. Tässä soveltamisstandardissa esitetään suositus, mitkä ominaisuudet on ilmoitettava ko. tuotestandardien mukaan CE-merkityille päällystekivituotteille (betoniset päällystekivet, -laatat ja -reunakivet sekä luonnonkivestä tehdyt päällystelaatat, noppa ja nupukivet ja reunakivet) eri käyttökohteissa sekä niille ominaisuuksille asetetut vähimmäisvaatimustasot tai luokat.

ISO 10874:2009 establishes a classification system for resilient, textile, laminate and and modular mechanical locked floor coverings floor coverings. The classification is based on practical requirements for areas of use and intensity of use and is linked to the requirements specified in the relevant International Standard for each type of floor covering. ISO 10874:2009 is also intended to provide guidance for manufacturers, specifiers and consumers, to enable them to choose the appropriate class of floor covering for any given area of use or specific room.

This document specifies requirements and test methods for durability, strength, security and function of devices that restrict the opening of windows and door height windows to a maximum opening width. Depending on the requirements imposed in Member States on the basis of building regulations or in tenders for window or door height windows, the hardware manufacturer designs the restrictors to allow opening widths of for example max. 89 mm, max. 100 mm or max. 120 mm; for the use of restrictors in building components. This document does not apply to a) restrictors with an opening width limitation of more than 120 mm; b) child protective window restrictors intended to be installed by the end consumers; such restrictors from the DIY market are covered in EN 16281; c) restrictors for window designs with sliding sashes. NOTE 1 Restrictors and reverse restrictors can be either a separate item of hardware or an integral part of hardware, for example a part of the operating gear or an integral part of a hinge. NOTE 2 It is possible to use more than one restrictor on a single window. NOTE 3 The requirements included within this document take the needs for child safety into consideration. This document applies to restrictors that are intended to be factory installed in windows and door height windows by specialist companies in their production facilities.

1.1 Scope of EN 1995-3 (1) This document gives minimum requirements for execution of timber structures (buildings and bridges) designed in accordance with EN 1995 (all parts) to ensure that what is built meets the requirements for mechanical resistance, serviceability, durability, and fire performance. (2) This document gives guidance on moisture control during transport to the building site, storage on site, handling on site and erection. (3) This document gives guidance on workmanship and deviation limits during execution. (4) This document assumes that there is an execution specification which states all the specific requirements relevant for the execution of a particular structure. (5) For products covered by a European technical product specification, this document only covers those aspects of fabrication such as cutting, machining and drilling after placement of the product on the market. (6) This document does not cover: a) parts which are not designed according to EN 1995; b) temporary works (such as formwork, scaffolding, propping, shoring, etc.); c) specification, production and conformity of timber members in accordance with European technical product specifications; d) deviation limits for other properties than mechanical resistance, serviceability, durability and fire performance; e) contractual aspects, responsibilities of the various parties, competency requirements or the degree of independence of the personnel undertaking the inspection; f) health and safety requirements during execution. 1.2 Assumptions (1) It is assumed that all relevant provisions of EN 1995 are complied with. (2) It is recognized in this document that areas such as detailed requirements for competence of personnel, and details related to Quality Management are within the competence of the CEN Member States. (3) Before the execution begins on a part of the structure, it is assumed that the following are available on site: — the drawings and specification of that part; — the execution specification. (4) Before the start of the execution, it is assumed that the execution specification has been checked for completeness. (5) It is assumed that previous work (such as foundations) has been inspected and that any work which needs to be done due to deviations from the execution specification has been carried out.

1.1 Scope of prEN 1995-1-1 (1) prEN 1995-1-1 gives general design rules for timber structures. (2) prEN 1995-1-1 also gives specific design rules for buildings and timber civil engineering works. 1.2 Assumptions (1) The assumptions of EN 1990 apply to this document. (2) prEN 1995-1-1 is intended to be used in conjunction with EN 1990, EN 1991 (all parts), EN 1998 (all parts) when timber structures are built in seismic regions.

1.1 Scope of EN 1995-1-2 (1) This document deals with the design of timber structures for the accidental situation of fire exposure and it is intended to be used in conjunction with EN 1995-1-1 and EN 1991-1-2. This document only identifies differences from, or supplements to, normal temperature design. (2) This document applies to timber structures required to fulfil a loadbearing function, separating function or both. (3) This document gives principles and application rules for the design of structures for specified requirements in respect of the aforementioned functions and the levels of performance. (4) This document applies to structures, or parts of structures, that are within the scope of EN 1995-1-1 and are designed accordingly. (5) The methods given in this document are applicable to all products covered by European technical product specifications made reference to in this document. 1.2 Assumptions (1) In addition to the general assumptions of EN 1990, the following assumptions apply: - the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel, or is given by the relevant national regulation; - any fire protection measure taken into account in the design will be adequately maintained.

(1) This document gives design rules for the structural parts of bridges made of timber or other wood-based materials, either singly or compositely with concrete, steel or other materials. (2) The provisions of this document supplement, and in some cases modify or supersede, provisions given EN 1995-1-1. (3) Prestressed timber-concrete composite (TCC) members are not covered by this document. The design of stress-laminated timber decks used as part of a TCC system is covered. (4) TCC structures which rely on friction between wood and concrete are not covered by this document.

EN 1998-1-2 is applicable to the design and verification of new buildings and temporary structures in seismic regions.

(1) This document provides provisions for the assessment of existing structures, including geotechnical structures, and the general principles for interventions, to be used in conjunction with prEN 1990-1. NOTE This document is based on the general requirements and principles of structural reliability provided in prEN 1990-1. (2) Unless otherwise specified, prEN 1990-1 applies. (3) This document covers general principles regarding actions for assessment, complementing EN 1991 (all parts). NOTE Provisions for seismic actions due to earthquake are provided in EN 1998-3. (4) This document does not cover the design of new structural parts that will be integrated into an existing structure. NOTE For the design of new structural parts, see prEN 1990-1. (5) This document does not provide: — specific rules for initiation of assessment; — specific rules on how to undertake interventions that may be carried out as a result of an assessment; — material-specific technical provisions for existing structures; — provisions for seismic assessment and retrofitting of existing structures. NOTE For provisions for seismic assessment and retrofitting of existing structures, see EN 1998-3.

1.1 Scope of !EN 1990-1 (1) This document establishes principles and requirements for the safety, serviceability, robustness and durability of structures, including geotechnical structures, appropriate to the consequences of failure. (2) This document is also applicable for existing structures as specified in EN 1990-2. (3) This document is intended to be used in conjunction with the other Eurocodes for the design of buildings and civil engineering works, including temporary structures. (4) This document describes the basis for structural and geotechnical verification according to the limit state principle. (5) The verification methods in this document are based primarily on the partial factor method. NOTE 1 Alternative methods are given in the other Eurocodes for specific applications. NOTE 2 The Annexes to this document also provide general guidance concerning the use of alternative methods. deleted text (6) This document is also applicable for the design of structures where materials or actions outside the scope of EN 1991 (all parts) to EN 1999 (all parts) are involved. NOTE In this case, additional or amended provisions can be necessary. 1.2 Assumptions (1) It is assumed that reasonable skill and care appropriate to the circumstances is exercised in the design, based on the knowledge and good practice generally available at the time the structure is designed. (2) It is assumed that the design of the structure is made by appropriately qualified and experienced personnel. (3) The design rules provided in the Eurocodes assume that: - execution will be carried out by personnel having appropriate skill and experience; - adequate control and supervision will be provided during design and execution of the works, whether in factories, plants, or on site; - construction materials and products for new structures or new structural members will be used in accordance with the Eurocodes, the relevant product and execution standards, and project specifications; - the structure will be adequately inspected and maintained; - the structure will be used in accordance with the assumptions. NOTE Guidance on management measures to satisfy the assumptions for design, verification and execution is given in Annex B.

This document specifies the test method and performance metrics to evaluate the behaviour of a vehicle equipped with door open warning system during several accidental scenarios. These potential accidents occur when a door is about to be opened and there is a risk of collision due to the vehicle door opening. This document applies to category M1 and N1 vehicles equipped with a door open warning system. NOTE Depending on accidentology, only a part of the scenarios can be used for an evaluation of performance.

This document specifies the conformance test plan for the CAN data link layer and the physical coding sublayer standardized in ISO 11898-1:2024. This includes the implementation options in accordance with ISO 11898-1:2024, C1. CAN FD light as defined in the Annex A of 11898-1 is not covered by this document.

This document provides requirements on the workflow and quality assessment of single cell RNA sequencing (scRNA-seq) data processing for eukaryotic cells. This document provides guidelines for raw data quality control, alignment and mapping, and cell barcode correction for single cell RNA sequencing. This document specifies the requirements for visualization and cell type identification of scRNA-seq data.

This document specifies test procedures for the acquisition and presentation of multipoint data which demonstrate the behaviour of plastics under the following environments: —    prolonged exposure to heat; —    liquid chemicals; —    environmental stress cracking under a constant tensile stress; —    artificial weathering. The tests are listed in order of increasing severity of the environment. By testing under the least severe environments first, it is possible to make informed judgements regarding whether tests under more severe conditions are worthwhile.

This document specifies test procedures for the acquisition and presentation of multipoint data which demonstrate the behaviour of plastics under the following environments: — prolonged exposure to heat; — liquid chemicals; — environmental stress cracking under a constant tensile stress; — artificial weathering. The tests are listed in order of increasing severity of the environment. By testing under the least severe environments first, it is possible to make informed judgements regarding whether tests under more severe conditions are worthwhile.

This document specifies a method for determining the film hardness by pushing pencils of known hardness over the film. The test can be performed on a single coating of a paint, varnish or related product, or on the upper layer of a multi-coat system. This rapid test has not been found to be useful in comparing the pencil hardness of different coatings. It is more useful in providing relative ratings for a series of coated panels exhibiting significant differences in pencil hardness. The method is applicable only to smooth surfaces.

ISO 15110:2017 specifies a so-called acid dew and fog test (ADF test) as an accelerated laboratory test method for simulating, by the use of artificial acidic precipitation, the damaging effects of acidic atmospheric precipitation in association with UV radiation, neutral condensed precipitation, and changing temperature and humidity. This test method is intended to be used in evaluating, on the basis of relative performance rankings, the suitability of painted materials for use in outdoor environments with acidic precipitation. It is not intended to generate the same extent of damage or the same damage pattern as in outdoor weathering, but rather to give a ranking which is similar to that which would be obtained in outdoor weathering. The method produces damage which is more homogeneous, allows fewer specimens to be exposed (and hence more rapid testing) and enables evaluation of the exposed specimens to be carried out using methods which are more objective than visual assessment.

WARNING The electronic file of this document contains colours which are considered to be useful for the correct understanding of the document. Users should therefore consider printing this document using a colour printer. This document specifies a method for determining the film hardness by pushing pencils of known hardness over the film. The test can be performed on a single coating of a paint, varnish or related product, or on the upper layer of a multi-coat system. This rapid test has not been found to be useful in comparing the pencil hardness of different coatings. It is more useful in providing relative ratings for a series of coated panels exhibiting significant differences in pencil hardness. The method is applicable only to smooth surfaces.

This document specifies a so-called acid dew and fog test (ADF test) as an accelerated laboratory test method for simulating, by the use of artificial acidic precipitation, the damaging effects of acidic atmospheric precipitation in association with UV radiation, neutral condensed precipitation, and changing temperature and humidity. This test method is intended to be used in evaluating, on the basis of relative performance rankings, the suitability of painted materials for use in outdoor environments with acidic precipitation. It is not intended to generate the same extent of damage or the same damage pattern as in outdoor weathering, but rather to give a ranking which is similar to that which would be obtained in outdoor weathering. The method produces damage which is more homogeneous, allows fewer specimens to be exposed (and hence more rapid testing) and enables evaluation of the exposed specimens to be carried out using methods which are more objective than visual assessment.

This document summarizes descriptive quantities for those responsible (e.g. scientists, safety engineers) for determination of postures for a seated person who is exposed to whole-body vibration. This document specifies a methodology for assessing the health risk of individuals exposed to whole-body vibration (WBV) that includes the addition of posture effects. This document defines an accumulative posture index that is applied to the daily overall frequency-weighted root-mean-square (r.m.s.) acceleration to establish a combined daily vibration exposure for assessing health risk.  This document is limited to the seated person subjected to WBV and health risk assessment using the ISO/DIS 2631-1 [1] basic evaluation method. It does not apply to standing or recumbent (supine) persons. This document does not include regional lumbar support or measurement of lumbar lordosis verses lumbar kyphosis. This document does not consider transient vibration or regular or occasional shocks.